How To Replace Bathtub Without Access
The stem is the thin pipe shape that extends out from the wall and controls the faucet. Now take a pencil and mark the reference line of all the studs all the way around your bathtub.
Tub Decks And Access Panels Ceramic Tile Advice Forums John Bridge Ceramic Tile Tub Tile Tub Surround Bathroom Design
Put the new faucet in.
How to replace bathtub without access. With the water lines off disconnect the mounting nuts that hold the tub faucet onto the wall or tub. Use a pencil and straight edge and mark the outer boundaries of the access port in the form of a square for easier renovation after you have repaired your jetted tub. Then remove the tub spouts drains and drain shoe and.
Purchase a tub that fits in the remaining hole. Unhook water lines and lock nuts from faucet stems. Prepare the new tub faucet.
One side is bigger than the other so it fits several sizes. Mark your access port with sufficient height and width to maneuver within with tools in your hands. Lay a bead of plumbers putty around the tub faucet plate then push the faucet into position against the wall.
Remove the tub from the box and position the new tub into the hole. You may have to cut out a portion of the drywall backing behind the shower but drywall is comparatively easy and cheap to replace. Once done remove your tub and put it aside.
Installing a new stringer With your studs and rivets marked you will need to take the height of your bathtub and. Without it the only way to fix the plumbing is to cut a hole in the wall. Cut through the grout around the tiles to be removed with a grout saw then try to pry the tiles off with a putty knife or pry bar.
To replace a bathtub first youll need to cut a hole in the wall behind your tub and turn off the water supply to your bathroom. The set screw may be in the back like the faucet or at the very top of the handle. You will rip the drywall or backerboard behind them.
Repeat this same process with the handles. Lay the bathtub on its side so you can easily access the drain holes from underneath and from the top. The tub should have the drain hole oriented on the proper side of the bathtub for your bathroom unless you plan to relocate the existing plumbing.
How to Replace Tub Faucets With No Wall Access Turn off the water valves at the main incoming water pipe. Insert a screwdriver through the holes in the sides of the key and use it as a lever to turn the flange counterclockwise. Use a socket wrench to unscrew the stem from your faucet.
If youre using a drain key insert it in the opening of the old drain. Slide a hollow socket wrench tool over the stem and push it over the hex nut. Grip the wrench with a pair of pliers and twist it counterclockwise.
Hold the large hex nut on the body of. Rotate the key counter clockwise with a screw driver through the body of the key. Then pull the tub faucet off and clean the wall surface behind it.
Crawling through your crawl space will also require old clothes that cover your arms and legs as well as a mask to protect your lungs from any fiberglass fibers. Unscrew any remaining elements at the base of the faucet with your screwdriver. Remove the cap on the faucet handle and loosen the screw underneath with an Allen wrench.
Remove the screws holding the escutcheon plate in place and slide out the escutcheon. Insert the Drain Key into the drain. If the wall is tiled and you have a plumber youll be paying him to make a big mess in the bathroom.
Pry out the clip around the cartridge with a pair of needle. Use a screwdriver to disconnect and remove the tubs waste and overflow valve cover. If you dont have an access panel behind the tub and shower when problems arise youll wish you did.
To change a bathtub cartridge begin by removing the handle as described in Step 1. Go back in bathroom - pull the faucet out. You may need to slip a putty knife between the base of the faucet and tub deck if its been caulked or sealed.
Keep turning until the flange comes loose and you can remove it. Remove the retaining clip that. Use a tool designed for tub drain removal called a tub drain wrench to remove the drain flange.
When connecting the drain the rubber gasket goes between the drain elbow and the bathtub not on top of the bathtub. You can disconnect the old drain and overflow from the inside of the tub then lift and remove the old tub. Then take a drain assembly sold in kits and start by attaching the drain and the overflow drain to the bathtub.
How To Remove And Replace A Bathtub Terry S Plumbing
I Need To Do This For My Tub That Still Has All It S Pipes And Tubes Exposed After 3 5 Years Tub Surround Bathtub Remodel Bathtub Tile
Build A Frame Around A Bathtub And Install Tiling For A Built In Bathtub If You Can Try To Make A Door Or Basement Bathroom Design Built In Bathtub Bathtub
Pin On Aging In Place
